/ Docs



Install Livepeer Client

Video Developers

Getting Started


Video Miners

How-to Guides

Set Session Limits

video miners


how to guides

Set Session Limits


Session limits

Session limits allow orchestrators and transcoders to manage transcoding capacity. When session limits are set properly, orchestrators and transcoders will be able to maximize work received while also protecting against performance degradation due to overload.

By default, the session limit on orchestrators and transcoders is set to 10. Whenever the number of concurrent sessions goes above this, orchestrators return an OrchestratorCapped error to the broadcaster and transcoders will stop receiving work from orchestrators. The appropriate session limit will vary depending on available hardware and bandwidth.

Calculate session limits

Calculate the session limit based on (1) transcoding hardware and (2) bandwidth as explained below, and take the minimum of the two. Finally, pass it through the -maxSessions parameter to your node as explained above.

The bandwidth and computational power needed to transcode a video stream varies with the source video and requested outputs' configuration. Thus any session limit estimate only serves as a ballpark, and you may want to tweak it after some real use on the network.

The steps below assume that the incoming streams are configured with the most-commonly found Adaptive Bitrate (ABR) ladder on the network. You may calculate it similarly for a different ABR ladder.

Evaluate hardware

The following assumes that you have livepeer_bench installed and have the common output rendition configuration stored in a file called transcodingOptions.json.

You can use the following script to benchmark transcoding for a range of concurrent sessions:

for i in {1..20}
    ./livepeer_bench \
        -in bbb/source.m3u8 \
        -transcodingOptions transcodingOptions.json \
        -nvidia 0 \ # Only required for transcoding with Nvidia GPUs
        -concurrentSessions $i |& grep "Duration Ratio" >> bench.log

If you are transcoding with multiple identical Nvidia GPUs, benchmarking with a single GPU should suffice and then you can multiply the limit for a single GPU by the number of available GPUs. If you are transcoding multiple different Nvidia GPUs, you should benchmark each unique GPU and determine a limit that is specific to that GPU.

You can adjust the loop range ({1..20}) to reflect the maximum number of concurrent sessions that you want to benchmark. If the real-time duration is still below 1.0 at 20 maximum concurrent sessions then you should increase the maximum number of concurrent sessions. If you are transcoding with a CPU, you will likely want to adjust the maximum number of concurrent sessions to a smaller value (i.e. 5).

You will see the final output in a file called bench.log:

| * Real-Time Duration Ratio * | <Ratio> |    // Concurrent Session Count 1
| * Real-Time Duration Ratio * | <Ratio> |    // Concurrent Session Count 2
| * Real-Time Duration Ratio * | <Ratio> |    // Concurrent Session Count 20

The recommendation for determining a hardware level limit is to use the concurrent sessions value of the last log indicating that the real-time duration ratio X was less than or equal 0.8 which leaves a ~20% buffer for upload/download within real-time.

Evaluate bandwidth

The most common output rendition configuration found on the network is (assuming source is 1080p30fps):

| Resolution & Fps       | Bitrate  |
| 1080p30fps             | 6000kbps |
| 720p<source>fps        | 3000kbps |
| 480p<source>fps        | 1600kbps |
| 360p<source>fps        | 800kbps  |
| 240p<source>fps        | 250kbps  |

For a single stream you will require 6000 kbps for downloading the source rendition and 5600 kbps for uploading the output renditions. Thus, you will roughly need:

Download Bandwidth = 6 Mbps Per Stream

Upload Bandwidth = 5.6 Mbps Per Stream

To get an idea of the number of streams you can handle, divide the above from your network provider's limits. For example a typical broadband connection with upstream/downstream of 100 Mbps should serve ~16 streams reliably. You can probably stretch it by ~20% more as not all streams' segments would be processed at the same time. You may want to refer to some suggestions in the bandwidth requirements around testing your available upload/download bandwidth.

Derive a session limit based on hardware and bandwidth

Once you have calculated a hardware level limit and a bandwidth level limit, take the minimum of the two and use that as your session limit which is set via the -maxSessions flag.

Session management in orchestrators and transcoders is still constantly being improved so in practice, your mileage may vary with this approach - you may find that your orchestrator or transcoder performance may be better or worse with a higher session limit. Further experimentation with tweaking the session limit values after performing real work on the network is recommended.

Set session limits

The -maxSessions flag is used to set session limits on both orchestrators and transcoders.

Example of sessing the session limit to 30 for a combined orchestrator and transcoder (other flags omitted):

livepeer \
    -orchestrator \
    -transcoder \
    -maxSessions 30


Benchmark Transcoding


Monitor Metrics

Pre-requisitesSession limitsCalculate session limitsEvaluate hardwareEvaluate bandwidthDerive a session limit based on hardware and bandwidthSet session limits